| 招标信息 | |||
|---|---|---|---|
| ？？招标单位 | 龙口市正和商贸有限公司 | 项目名称 | 螺丝 |
| ？？招标联系人 | 无 | 手机 | 无 |
| ？？联系电话 | 无 | 联系邮件 | zhaobiao@nanshan.com.cn |
| ？？质保期 | 报名截止日期 | ||
| ？？招标邮箱 | zhaobiao@nanshan.com.cn | ||
| 竞标保证金信息 | |||
|---|---|---|---|
| ？？项目保证金 | 5000.00元 | 帐户名称 | 山东新南铝材科技开发有限公司 |
| ？？帐号 | 233832812142 | 开户行 | 中国银行龙口南山支行 |
| ？？备注 | |||
| 备注：竞价保证金汇款只接受公司转账，不支持个人名义转账或银行柜台现金转账。 | |||
| 供应审计部招标联系人信息 | |||
|---|---|---|---|
| ？？标书联系人 | 无 | 办公电话 | 无 |
| ？？邮件 | 无 | ||
| 标书汇款相关信息 | |||
|---|---|---|---|
| ？？账户名称 | 无 | 账号 | 无 |
| ？？开户行 | 无 | 行号 | 无 |
| ？？标书收费标准 | 地址、电话 | 无 | |
| 备注：标书费汇款只接受公司转账，不支持个人名义转账或银行柜台现金转账。注明标书费的用途或投标项目名称。 | |||
| 物品名称 | 规格型号 | 数量 | 单位 | 描述 |
|---|---|---|---|---|
| 螺帽 | {"直径":"6","材质":"中碳钢并经过热处理","性能等级":"8.8","使用寿命":"12月","参照标准":"GB/T 1229-2006"} | 6283.00 | 个 | |
| 弹垫 | {"直径":"M10","材质":"弹簧钢","性能等级":"8.8"} | 5700.00 | 个 | |
| 镀锌平垫 | {"直径":"14","材质":"钢，表面镀锌"} | 2750.00 | 个 | |
| 1型非金属嵌件六角锁紧螺母 | {"直径":"M6","材质":"304不锈钢","表面处理":"无","性能等级":"A2-70, 锁紧塑圈材质尼龙","特殊要求":"螺母拥有自锁功能","使用寿命":"365天","参照标准":"GB/T 889.1","备注":"产品完好无破损，符合上述技术要求，附带合格证。不合格品处理标准：如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 500.00 | 个 | |
| 内六角螺丝 | {"直径":"6","螺纹长度":"20mm","材质":"45#钢","性能等级":"8.8"} | 6000.00 | 个 | |
| 平垫 | {"直径":"M16","厚度":"2mm","材质":"65Mn钢","表面处理":"表面镀锌","性能等级":"200HV","使用寿命":"365天","参照标准":"GB/T 3098.26-2021","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} | 14214.00 | 个 | |
| 外六角螺丝 | {"直径":"6mm","长度":"50mm","材质":"低碳钢"} | 2928.00 | 个 | |
| 开口销 | {"规格型号":"Φ4*70","材质":"Q235","使用寿命":"6月","参照标准":"GB/T 91-2000"} | 200.00 | 个 | |
| 不锈钢平垫 | {"直径":"M10","材质":"不锈钢304","使用寿命":"＞180天"} | 500.00 | 个 | |
| 全丝内六角螺丝 | {"直径":"M6mm","长度":"25mm","图号":"M6*25","螺纹长度":"25mm","材质":"碳钢","表面处理":"发黑处理","性能等级":"12.9级","使用寿命":"不低于150天","参照标准":"GB/T 3098.1-2010"} | 2200.00 | 套 | |
| 不锈钢弹簧垫 | {"直径":"M12","材质":"不锈钢316","使用寿命":"730天"} | 4160.00 | 个 | |
| 不锈钢螺帽 | {"直径":"M8mm","高度":"6.5mm","材质":"不锈钢304","表面处理":"抗氧化","性能等级":"4.8级","使用寿命":"＞1095天","参照标准":"GB/T 41-2016","备注":"当验收不符合技术要求时，需进行退换货处理，期间所产生的运输费用由供货商承担。"} | 500.00 | 个 | |
| 平垫 | {"直径":"20","材质":"45H碳钢","性能等级":"黑"} | 5650.00 | 个 | |
| 钻尾自攻自钻螺钉 | {"直径":"5.5mm","长度":"75mm","材质":"CH1022A","性能等级":"4.8级","表面处理":"电镀，镀层光亮","特殊要求":"无","参照标准":"GB/T 156856.4-2002"} | 156160.00 | 个 | |
| 不锈钢沉头螺丝 | {"直径":"M6mm","长度":"25mm","图号":"无","螺纹长度":"21mm","材质":"304不锈钢","表面处理":"酸洗，光亮","性能等级":"A2-70","使用寿命":"730天","参照标准":"GB/T 3098.6-2014","备注":"规格：M6*1*25mm，外观：不能有毛刺，不得有裂纹和明显缺陷 设备紧固件，到货物资达不到技术要求，供货厂家无偿退换货，退换货所产生的费用由厂家自行承担。"} | 1000.00 | 个 | |
| 平垫 | {"直径":"M22","厚度":"3mm","材质":"Q235B","表面处理":"镀锌","性能等级":"100HV","使用寿命":"≥365天","参照标准":"GB/T 95-2002","备注":"验收标准:到货与技术要求不符时,供应商无条件退换货处理。"} | 140.00 | 个 | |
| 平垫圈A级 | {"直径":"M12","厚度":"2.5","材质":"304不锈钢","表面处理":"不处理","性能等级":"200HV","使用寿命":"1095天","参照标准":"GB/T 97.1","备注":"平垫圈A级/φ12/200HV/304不锈钢/产品完好无破损，符合上述技术要求，附带合格证。不合格品处理标准：如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 10477.00 | 个 | |
| 外六角螺母 | {"直径":"M16","高度":"15.9mm","材质":"45#碳钢","表面处理":"无","性能等级":"8.8级","使用寿命":"730天","参照标准":"GB/T 6170-2015","备注":"如不符合技术要求供应商予以无条件退换处理。"} | 6454.00 | 个 | |
| 镀锌平垫 | {"规格型号":"Φ33*Φ12.5*2MM","内径":"12.5mm","外径":"Φ33mm","厚度":"2mm","材质":"Q235B (表面镀锌)","参照标准":"GB/T 16938-2008"} | 181000.00 | 个 | |
| 内卡簧 | {"规格型号":"Ф35","材质":"钢","使用寿命":"360天"} | 50.00 | 个 | |
| 内六角螺栓 | {"直径":"6","长度":"60mm","材质":"45H碳钢","性能等级":"12.9","使用寿命":"6-12月","参照标准":"GB/T 3098.1-2010"} | 6000.00 | 个 | |
| 平垫 | {"直径":"24","材质":"45H碳钢","使用寿命":"12月","参照标准":"GB/T 5286-1985"} | 544.00 | 个 | |
| 外六角螺栓 | {"直径":"M12","长度":"35mm","材质":"低碳钢","性能等级":"4.8级","使用寿命":"180天","参照标准":"GB/T 5782-2016"} | 795.00 | 个 | |
| 内六角螺栓 | {"直径":"M10","长度":"55mm","螺纹长度":"55mm","材质":"碳钢","性能等级":"8.8","使用寿命":"180天"} | 230.00 | 个 | |
| 不锈钢外六角螺丝 | {"直径":"M6","长度":"25mm","图号":"M6*25","螺纹长度":"25mm","材质":"不锈钢304","表面处理":"0","性能等级":"A2-70","使用寿命":"360天","参照标准":"GB/T 3098.6-2014","备注":"全丝螺栓,螺丝丝扣均匀,无断丝,缺丝现象"} | 464024.00 | 个 | |
| 热镀锌螺帽 | {"直径":"M14","高度":"12.1~12.8mm","材质":"Q235","表面处理":"热镀锌","性能等级":"6级","使用寿命":"4380天","参照标准":"GB/T 6170-2015","备注":"热镀锌按照GB/T5267.3执行，来货必须附有产品材质证明（合格证），来货验收达不到技术要求，供货商应无条件给予退换货处理。（退换货产生的一切费用由供货商承担）"} | 6500.00 | 个 | |
| 外六角螺栓 | {"直径":"M6","长度":"100mm","图号":"M6*100","螺纹长度":"45mm","材质":"碳钢","表面处理":"镀锌","性能等级":"无","使用寿命":"365天","参照标准":"GB/T 5782-2016","备注":"螺丝丝扣均匀,非全丝,无断丝.缺丝现象."} | 4100.00 | 个 | |
| 不锈钢管卡 | {"规格型号":"10-16","公称直径":"10-16mm","公称压力":"2.5MPa","材质":"201不锈钢","参照标准":"JB/T 8870-1999"} | 410.00 | 个 | |
| 膨胀螺栓 | {"规格型号":"M6*80","直径":"6mm","长度":"80mm","强度等级":"4.8","表面处理":"镀蓝白锌","材质要求":"碳钢","配套附件":"无","参照标准":"JB/ZQ 4763-2006","备注":"使用寿命：消耗品"} | 500.00 | 套 | |
| I型六角螺母 | {"直径":"M12","高度":"10.8","材质":"304不锈钢","表面处理":"无","性能等级":"A2-70","使用寿命":"1095天","参照标准":"GB/T 6170","备注":"产品完好无破损，符合上述技术要求，附带合格证。不合格品处理标准：如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 2299.00 | 个 | |
| 外六角螺栓 | {"直径":"14","长度":"50","螺纹长度":"全丝","材质":"中碳钢","表面处理":"发黑","性能等级":"8.8"} | 2000.00 | 个 | |
| 螺帽 | {"直径":"M20","高度":"12.5mm","材质":"Q235","表面处理":"防锈处理","性能等级":"4.8","使用寿命":"720天","参照标准":"GB/T 41-2016","备注":"螺帽，规格20*12.5，材质Q235，表面防锈处理，参考标准GB/T 41-2016，不合格处理标准:如到货不符合技术要求,由供应商无条件进行更换,退货处理."} | 537.00 | 个 | |
| 外六角螺丝 | {"直径":"M12","长度":"60mm","图号":"M12*60","螺纹长度":"29-31mm","材质":"Q235","表面处理":"发黑","性能等级":"8.8","使用寿命":"180天","参照标准":"GB/T 16938-2008","备注":"1.外观良好,无断丝、错丝.\n2.到货验收不符合技术要求,必须退换货,产生的费用由供应商承担."} | 750.00 | 套 | |
| 弹簧 | {"规格型号":"0.8*17.8*15","材质":"60SI2MNA","所属设备":"除尘器","设备型号":"zz-1400","设备生产厂家":"国产","国产/进口":"国产","使用寿命":"≥365天","特殊要求":"长度：15mm；直径：17.8mm；钢丝直径：0.8mm；圈数：4圈","参照标准":"GB/T 2089-2009","备注":"验收标准：到货与技术要求不符时，供应商无条件退换货处理。"} | 500.00 | 个 | |
| 外六角螺栓 | {"直径":"12","长度":"75","螺纹长度":"全丝","材质":"Q235","性能等级":"4.8"} | 600.00 | 个 | |
| 不锈钢螺帽 | {"直径":"M12","高度":"10mm","材质":"不锈钢316L","使用寿命":"365天"} | 3280.00 | 个 | |
| 三角彩旗 | {"规格型号":"常规","颜色":"常规","外部材质":"布","外部克重":"0","内部材质":"布","内部克重":"0","特殊要求":"无"} | 500.00 | 米 | |
| 沉头螺栓 | {"直径":"M16","长度":"50mm","图号":"无","螺纹长度":"40mm","材质":"Q235","表面处理":"镀锌或发黑处理","性能等级":"4.8级","使用寿命":"≥180天","参照标准":"GB/T 3098.1-2010","备注":"粗牙牙距2mm,不符合技术要求,予以退换货处理,产生的费用由供货商承担."} | 179.00 | 个 | |
| 不锈钢可调管箍 | {"规格型号":"16-32","公称直径":"16-32mm","公称压力":"2.5MPa","材质":"304不锈钢"} | 160.00 | 个 | |
| 螺栓 | {"直径":"12","长度":"100","材质":"Q235B","性能等级":"4.8级"} | 100.00 | 个 | |
| 膨胀螺丝 | {"规格型号":"M12*120","直径":"16mm","长度":"120mm","强度等级":"4.8级","材质要求":"低碳钢"} | 50.00 | 套 | |
| 弹垫 | {"直径":"M6","材质":"弹簧钢","性能等级":"8.8"} | 500.00 | 个 | |
| 不锈钢喉箍 | {"规格型号":"22-32","公称直径":"22-32mm","公称压力":"2.5Mpa","长度":"50.5mm","连接方式":"螺杆","材质":"不锈钢304","特殊要求":"表面抛光","使用寿命":"365天","参照标准":"JB/T8870-1999"} | 56.00 | 个 | |
| 六角法兰面螺栓 | {"直径":"M12","长度":"30","图号":"/","螺纹长度":"30mm","材质":"304不锈钢","表面处理":"无","性能等级":"A2-70","使用寿命":"1095天","特殊要求":"无","参照标准":"GB/T 5789","备注":"产品完好无破损，符合上述技术要求，附带合格证。不合格品处理标准：如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 9200.00 | 个 | |
| 镀锌外六角螺栓 | {"直径":"11MM±0.5MM","长度":"180MM±4MM","材质":"Q235","表面处理":"镀锌","性能等级":"4.8级","参照标准":"GB/T 5781-2000"} | 178500.00 | 个 | |
| 不锈钢喉箍 | {"规格型号":"44-64","公称直径":"44~64mm","公称压力":"1.0Mpa","长度":"139mm~201mm","连接方式":"螺杆连接","材质":"304不锈钢","特殊要求":"最大可调直径64mm，最小可调直径44mm","使用寿命":"120天","参照标准":"JB/T 8870-1999","备注":"到货后包装完好无损，带有合格证，如果所送物品与技术参数不相符，必须给予退换货，产生一切费用由供货商全部承担"} | 10.00 | 个 | |
| 不锈钢可调喉箍 | {"规格型号":"25mm~51mm","公称直径":"无","公称压力":"无","长度":"25mm~51mm","连接方式":"无","材质":"不锈钢304","特殊要求":"如供应商供货与，提报计划不符要求供应商退换货处理！","使用寿命":"90天","参照标准":"JB/T 8870-1999"} | 500.00 | 个 | |
| 膨胀螺栓 | {"规格型号":"M14*80","直径":"18mm","长度":"80mm","强度等级":"4.8级","材质要求":"低碳钢"} | 500.00 | 套 | |
| 外六角螺丝 | {"直径":"16","长度":"150","材质":"碳钢","性能等级":"8.8"} | 130.00 | 个 | |
| 不锈钢管卡 | {"规格型号":"Φ32-44","公称直径":"32-44mm","公称压力":"2.5MPa","材质":"201不锈钢","使用寿命":"≥1年","参照标准":"JB/T 8870-1999"} | 100.00 | 个 | |
| 螺栓 | {"直径":"20","长度":"80mm","螺纹长度":"80mm","材质":"低碳合金钢","性能等级":"8.8级","参照标准":"GB/T 5782-2016"} | 2522.00 | 个 | |
| 不锈钢管卡 | {"规格型号":"44-64","公称直径":"44-64mm","公称压力":"2.5MPa","材质":"304不锈钢","参照标准":"JB/T 8870-1999"} | 500.00 | 个 | |
| 孔用卡簧 | {"规格型号":"D120/D130","材质":"碳钢","使用寿命":"365天"} | 500.00 | 个 | |
| 膨胀螺丝 | {"规格型号":"M16*150","直径":"16mm","长度":"150mm","强度等级":"8.8","表面处理":"表面镀锌处理","材质要求":"碳钢","配套附件":"螺帽、垫片等","参照标准":"JB/ZQ 4763-2006","备注":"使用寿命：1年"} | 80.00 | 个 | |
| 不锈钢螺丝 | {"直径":"M12mm","长度":"50mm","图号":"M12*50","螺纹长度":"50mm","材质":"不锈钢304","表面处理":"无","性能等级":"A2-70","使用寿命":"≥365天","参照标准":"GB/T 3098.6-2014","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} | 1900.00 | 个 | |
| 高强螺栓 | {"直径":"16","长度":"60","螺纹长度":"60mm","材质":"低碳合金钢或中碳钢并经过热处理","性能等级":"10.9"} | 8924.00 | 个 | |
| 不锈钢管卡 | {"规格型号":"64-76","公称直径":"64~76mm","公称压力":"1.0Mpa","长度":"260mm±5mm","连接方式":"螺杆连接","材质":"304不锈钢","特殊要求":"到货无变形","使用寿命":"≥365天","参照标准":"JB/T 8870-1999","备注":"验收标准：到货与技术要求不符时，供应商无条件退换货处理。"} | 470.00 | 个 | |
| 外六角螺栓 | {"直径":"M14","长度":"180mm","材质":"碳钢","性能等级":"8.8","参照标准":"GB/T 3098.1-2010"} | 3506.00 | 个 | |
| 不锈钢管卡 | {"规格型号":"110-130","公称直径":"110~130mm","公称压力":"1.0Mpa","长度":"435mm","连接方式":"螺杆连接","材质":"304不锈钢","特殊要求":"到货无变形","使用寿命":"≥365天","参照标准":"JB/T 8870-1999","备注":"验收标准：到货与技术要求不符时，供应商无条件退换货处理。"} | 200.00 | 个 | |
| 膨胀螺丝 | {"规格型号":"Ф18*150","直径":"22mm","长度":"150mm","强度等级":"4.8级","材质要求":"低碳钢"} | 100.00 | 套 | |
| 钢丝绳卡扣 | {"规格型号":"Φ15","材质":"45#钢，外部镀锌","使用寿命":"≥720天","参照标准":"GB/T 5976-2006","备注":"到货产品必须符合技术要求，达不到技术要求的厂家必须无条件退换货物。"} | 56.00 | 个 | |
| 双头螺栓 | {"直径":"M20","长度":"120mm","图号":"无","螺纹长度":"≥45mm","材质":"碳钢","表面处理":"无","性能等级":"4.8级","使用寿命":"730天","特殊要求":"1.两端螺纹长度≥45mm,螺距:2.5mm,2.国产通用件.3.验收标准:如到货与技术要求不符,供应商应无条件进行退,换货处理.","参照标准":"GB/T 953-1988"} | 286.00 | 个 | |
| 不锈钢管卡 | {"规格型号":"Φ350","公称直径":"Φ350mm","公称压力":"2.5MPa"} | 500.00 | 个 | |
| 不锈钢管卡 | {"规格型号":"210-250","公称直径":"210-250mm","公称压力":"2.5MPa","材质":"304不锈钢"} | 50.00 | 个 | |
| 斗提螺栓 | {"直径":"M10","长度":"50mm","图号":"无","螺纹长度":"35mm","材质":"Q235钢","表面处理":"发黑","性能等级":"8.8级","使用寿命":"120天","特殊要求":"每套螺栓配斗提专用垫一个、螺母一个","参照标准":"GB/T 16938-2008","备注":"到货不合格处理标准：如到货后验收不符合技术要求,供货商应免费给予退换货处理."} | 3200.00 | 个 | |
| 镀锌全丝杆 | {"直径":"M0.008","长度":"3000mm","材质":"Q235","表面处理":"镀锌,螺纹清晰,镀锌层不应有剥离,起皮,凸起,花斑,伤痕等现象","使用寿命":"3650天","性能等级":"4.8"} | 53355.00 | 支 | |
| 铁钉 | {"长度":"100±5mm","直径":"4±0.3mm","表面处理":"圆钉应经磨光处理，磨光后的圆钉表面应该是清洁和光亮并无显著伤痕。高强度，耐腐蚀，高硬度；","材质":"Q235","特殊要求":"钉帽：（8-10）mm;圆钉的次钉率和废钉率的总和不得超过8%；废钉率不得超过5%；"} | 9000.00 | 千克 | |
| 不锈钢管箍 | {"规格型号":"DN15","公称直径":"DN15mm","公称压力":"2.5MPa","材质":"不锈钢304"} | 500.00 | 个 | |
| 外六角螺栓 | {"直径":"20","长度":"130","材质":"碳钢","性能等级":"8.8"} | 1280.00 | 个 | |
| 内六角螺丝 | {"直径":"M20","长度":"140mm","材质":"45H钢","性能等级":"12.9","使用寿命":"365天"} | 42.00 | 个 | |
| 丝母止退垫片 | {"直径":"M80","内径":"81","外径":"103","材质":"Q235A","表面处理":"表面氧化处理","性能等级":"100HV级","特殊要求":"必须配有合格证","使用寿命":"≥365天","参照标准":"GB/T 858-1988"} | 500.00 | 个 | |
| 双头螺栓 | {"直径":"M20","长度":"230mm","图号":"无","螺纹长度":">65mm","材质":"中碳钢","表面处理":"热处理（淬火、回火）","性能等级":"10.9","使用寿命":"180天","参照标准":"GB/T 5780-2000、GB/T 5781-2000、GB/T 5782-2000、GB/T 5783-2000","备注":"配2个螺帽及2个弹簧垫"} | 180.00 | 套 | |
| 铁排钉 | {"长度":"45mm","直径":"Φ2.1mm","表面处理":"涂胶均匀","材质":"Q235","允许偏差":"±1mm","特殊要求":"1、外观应光洁无锈蚀、无伤痕、排列整齐、涂胶均匀，无开胶断裂情况。2、排钉直径2.1±1mm，钉帽宽度6mm，长度公差±1mm。3、排版平整无明显凹凸不平现象、无胶赘，弹夹可顺利滑动关闭。","参照标准":"GB/T 701-2008","备注":"使用寿命：车间生产易耗品"} | 6000.00 | 千克 | |
| 铁排钉 | {"长度":"50mm","直径":"Φ2.1mm","表面处理":"涂胶均匀","材质":"Q235","允许偏差":"±0.1mm","特殊要求":"1、外观应光洁无锈蚀、无伤痕、排列整齐、涂胶均匀，无开胶断裂情况。2、排钉直径2.1±0.1mm，钉帽宽度6mm，长度公差±1mm。3、排版平整无明显凹凸不平现象、无胶赘，弹夹可顺利滑动关闭。","参照标准":"GB/T 701-2008","备注":"如发现质量不合格产品，予以退换货处理\n使用年限：车间一次性使用辅材"} | 10100.00 | 千克 | |
| 铁排钉 | {"长度":"42mm","直径":"Φ2.1mm","表面处理":"涂胶均匀","材质":"Q195","允许偏差":"±1mm","特殊要求":"1、外观应光洁无锈蚀、无伤痕、排列整齐、涂胶均匀，无开胶断裂情况。2、排钉直径2.1±1mm，钉帽宽度6mm，长度公差±1mm。3、排版平整无明显凹凸不平现象、无胶赘，弹夹可顺利滑动关闭。","参照标准":"GB/T 701-2008","备注":"使用寿命：车间生产易耗品"} | 2000.00 | 千克 | |
| 弹簧 | {"规格型号":"2*33*100","材质":"弹簧钢"} | 20.00 | 个 | |
| 不锈钢双头螺栓 | {"直径":"M16","长度":"150","图号":"M16","螺纹长度":"50mm","材质":"不锈钢304","表面处理":"无","性能等级":"8.8","使用寿命":"365天","特殊要求":"无","参照标准":"GB/T 3106-2016","备注":"验收标准:附带合格证,表面及螺纹无损伤,若不符合要求供货厂家要给予退货或换货."} | 1396.00 | 个 | |
| 平键 | {"型号":"16*10","宽度":"16mm","高度":"10mm","长度":"1000mm","材质":"碳钢Q235","使用寿命":"≥90天"} | 50.00 | 米 | |
| 双头螺栓 | {"直径":"M30","长度":"300mm","图号":"无","螺纹长度":">100mm","材质":"中碳钢","表面处理":"热处理(淬火、回火)","性能等级":"10.9","使用寿命":">180天","参照标准":"GB/T 5780-2000、GB/T 5781-2000、GB/T 5782-2000、GB/T 5783-2000","备注":"螺栓螺纹为细丝螺纹，螺距2mm，并配双螺帽带弹簧垫"} | 100.00 | 套 | |
| 方头螺栓 | {"直径":"24mm","长度":"120mm","螺纹长度":"70mm","材质":"45H碳钢","性能等级":"10.9级","使用寿命":"2~3月","参照标准":"GB/T 3098.1-2010"} | 250.00 | 个 | |
| 沉头螺栓 | {"直径":"24","长度":"130","螺纹长度":"65mm","材质":"低碳合金钢、做热处理","性能等级":"8.8级","使用寿命":"＞3月","参照标准":"GB/T 5780-2000"} | 500.00 | 个 | |
| 轴用弹性挡圈 | {"规格型号":"Φ90","材质":"65Mn","性能等级":"热处理后硬度大于40HRC","使用寿命":"365天","参照标准":"GB/T 894-2017","备注":"1、规格：轴径：90mm,内径：84.5-0.13~+0.54mm，厚度：3-0.08mm\n2、不允许有锈迹，表面不允许有凸出的毛刺，用卡簧钳张开一定角度后能正常回复。\n3、到货验收：若到货不符合技术要求，则供应商无偿进行换货或者退货。"} | 500.00 | 个 | |
| 不锈钢喉箍 | {"规格型号":"91-114","公称直径":"95mm","公称压力":"0.8Mpa","长度":"380mm","连接方式":"紧固连接","材质":"不锈钢304","特殊要求":"无","使用寿命":"180天","参照标准":"JB/T 8870-1999","备注":"到货产品必须符合技术要求,并且表面光滑,无裂纹,如果不符合技术要求的,供货厂家必须无条件退换货物."} | 30.00 | 个 | |
| 高强螺栓 | {"直径":"30","长度":"190","螺纹长度":"72mm","材质":"45#钢","参照标准":"GB/T 5782-2016"} | 150.00 | 个 | |
| 板锤螺栓 | {"直径":"24","长度":"193","螺纹长度":"150mm","材质":"45#钢","性能等级":"8.8","使用寿命":"1年","特殊要求":"头部椭圆形"} | 100.00 | 个 | |
| 膨胀螺栓 | {"规格型号":"M16*100/304","直径":"16mm","长度":"100mm","强度等级":"4.8","表面处理":"镀蓝白锌","材质要求":"304不锈钢","配套附件":"无","参照标准":"GB/T 22795-2008","备注":"使用寿命:消耗品;验收标准:到货后如不符合技术要求,供应商应无条件给予更换、退货"} | 500.00 | 个 | |
| 开口销 | {"规格型号":"Φ8*100","材质":"Q235表面镀锌","使用寿命":"180天","参照标准":"GB/T 91-2000","备注":"到货标准：外观完好无损，无锈蚀.如果供应商供货与提报计划不符.要求供应商退换货处理。"} | 500.00 | 个 | |
| 不锈钢管卡 | {"规格型号":"188-200","公称直径":"188~200mm","公称压力":"1.0Mpa","长度":"690mm±5mm","连接方式":"螺杆连接","材质":"304不锈钢","特殊要求":"带宽≥26mm，厚度≥1mm","使用寿命":"≥365天","参照标准":"JB/T 8870-1999","备注":"验收标准：到货与技术要求不符时，供应商无条件退换货处理。"} | 500.00 | 个 | |
| 1型六角螺母A级 | {"直径":"M16","高度":"12mm","材质":"35CrMoA-5","表面处理":"无","性能等级":"无","使用寿命":"2190天","参照标准":"GB/T 6170-2015","备注":"图纸上“GB6170B-86”被标注在“图号”栏内，经查询，其现在被“GB/T 6170-2015 1型六角螺母”替代。"} | 500.00 | 个 | |
| 平键 | {"型号":"28*16","宽度":"28mm","高度":"16mm","长度":"1000mm","材质":"Q235","使用寿命":"365天","参照标准":"GB/T 1096-2003","备注":"该到货产品与技术要求不符，对该到货产品进行10%处罚或调换退货，调换货产生的费用由供货方承担。"} | 20.00 | 米 | |
| 1型六角螺母A级 | {"直径":"M12","高度":"8mm","材质":"碳钢","表面处理":"无","性能等级":"8级","使用寿命":"2190天","参照标准":"GB/T 6170-2015","备注":"图纸上“GB6170-86”被标注在“图号”栏内，经查询，其现在被“GB/T 6170-2015 1型六角螺母”替代。"} | 500.00 | 个 | |
| 弹簧 | {"规格型号":"105*20*30*235","材质":"弹簧钢","所属设备":"成型机","设备型号":"10b/h","设备生产厂家":"洛阳震动机械有限公司","国产/进口":"国产","使用寿命":"730天","特殊要求":"无","参照标准":"GB/T 23935-2009","备注":"弹簧外径105mm,高度235mm,线径20mm,弹簧线中心距离:30mm"} | 104.00 | 个 | |
| 卷钉 | {"材质":"Q235","外观":"螺纹卷钉","直径":"φ2.8mm","长度":"75mm","表面处理":"浸漆处理","特殊要求":"钉径公差±0.2mm,钉长公差±3mm","参照标准":"GB/T 27704-2011","备注":"每箱20卷卷钉，每卷225支钉\n使用寿命;车间生产易耗品一次性辅材.\n发现质量不合格产品或与技术标准不符，进行退换货处理,期间产生费用由供货商承担."} | 2700.00 | 箱 | |
| 卷钉 | {"材质":"高线Q195","外观":"螺纹卷钉","直径":"φ3.8mm","长度":"128mm","表面处理":"浸漆处理","特殊要求":"钉径公差±0.3mm,钉长公差±3mm","参照标准":"GB/T 27704-2011","备注":"每箱10卷卷钉，每卷125支钉\n使用寿命;车间生产易耗品一次性辅材.\n发现质量不合格产品或与技术标准不符，进行退换货处理,期间产生费用由供货商承担."} | 60.00 | 箱 | |
| 皮带扣 | {"型号":"Φ12-14","材质":"35#钢","允许偏差":"±0.1mm","特殊要求":"每箱12盒，每盒8套，每套28组，适用输送带厚度：8mm-10mm，附带产品合格证及材质检测报告，若到货物资质量与技术要求不符时，厂家需无偿进行退换货。","参照标准":"GB/T 699-2015"} | 1.00 | 箱 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"1500mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求"} | 1968.00 | 支 | |
| 钢丝螺套 | {"规格型号":"M10*1.5*1D","螺纹外径":"无","五星外径":"无","螺杆长":"无","材质":"304不锈钢","螺纹镀锌层厚度":"无","外观":"光滑无毛刺，不允许有毛刺、压痕、划伤和裂纹等表面缺陷","螺纹长度":"安装后长度8.50mm-9.25mmmm","使用寿命":"365天","参照标准":"GB/T 24425.1-2009","备注":"钢丝螺套嵌入铝合金的螺纹孔中，形成标准的M螺纹，具有连接强度高，抗震、抗冲击、耐磨损等特点。自由状态圈数4.7-5.2，自由状态外径12.1mm-12.8mm，安装柄长度5.8mm-7.9mm，螺纹精度5H，产品完好无破损，符合上述技术要求，如到货不符号技术要求，由供应商无条件进行更换、退货。"} | 500.00 | 个 | |
| 六角头螺栓 | {"直径":"M16","长度":"80","图号":"无","螺纹长度":"43mm","材质":"35CrMoA","表面处理":"无","性能等级":"无","使用寿命":"2190天","参照标准":"GB/T 5782-2016","备注":"螺纹：M16*2.0；图纸上“GB/T5782-1986”被标注在“图号”栏内，经查工标网，已被“GB/T 5782-2016”替代。零部件供货时提供到货清单+合格证；合金等特殊材质件需提供材质检测报告单；如有特殊使用要求或说明则应在合格证上标明或附带说明书等资料。到货与本技术要求不符，厂家无条件免费退换货。"} | 500.00 | 个 | |
| 全丝内六角螺栓 | {"直径":"M18","长度":"60","图号":"/","螺纹长度":"60mm","材质":"碳钢","表面处理":"氧化发黑","性能等级":"8.8","使用寿命":"90天","参照标准":"GB/T 70.1-2008","备注":"1、外观良好，无断丝，无错丝，无锈蚀痕迹等缺陷，到货时附带出厂合格证。\n2、如到货验收不符合技术要求，供货商无条件给予退换货处理，因此产生的费用由供货商承担。\n3、国产件，不限定品牌厂家。"} | 500.00 | 个 | |
| 外六角螺丝 | {"直径":"M16","长度":"140mm","图号":"M16*140","螺纹长度":"44-46mm","材质":"Q235","表面处理":"发黑","性能等级":"8.8","使用寿命":"180天","参照标准":"GB/T 16938-2008","备注":"1.外观良好,无断丝、错丝.\n2.到货验收不符合技术要求,必须退换货,产生的费用由供应商承担."} | 500.00 | 套 | |
| 外六角螺丝 | {"直径":"M16","长度":"60mm","图号":"M16*60","螺纹长度":"56-58mm","材质":"Q235","表面处理":"发黑","性能等级":"8.8","使用寿命":"180天","参照标准":"GB/T 16938-2008","备注":"1.外观良好,无断丝、错丝.\n2.到货验收不符合技术要求,必须退换货,产生的费用由供应商承担."} | 500.00 | 套 | |
| 外六角螺丝 | {"直径":"M12","长度":"120mm","图号":"M12*120","螺纹长度":"30-32mm","材质":"Q235","表面处理":"发黑","性能等级":"8.8","使用寿命":"180天","参照标准":"GB/T 16938-2008","备注":"1.外观良好,无断丝、错丝.\n2.到货验收不符合技术要求,必须退换货,产生的费用由供应商承担."} | 500.00 | 套 | |
| 外六角螺丝 | {"直径":"M16","长度":"200mm","图号":"M16*200","螺纹长度":"44-46mm","材质":"Q235","表面处理":"发黑","性能等级":"8.8","使用寿命":"180天","参照标准":"GB/T 16938-2008","备注":"1.外观良好,无断丝、错丝.\n2.到货验收不符合技术要求,必须退换货,产生的费用由供应商承担."} | 500.00 | 套 | |
| 外六角螺丝 | {"直径":"M8","长度":"100mm","图号":"M8*100","螺纹长度":"25-27mm","材质":"Q235","表面处理":"发黑","性能等级":"8.8","使用寿命":"180天","参照标准":"GB/T 16938-2008","备注":"1.外观良好,无断丝、错丝.\n2.到货验收不符合技术要求,必须退换货,产生的费用由供应商承担."} | 500.00 | 套 | |
| 外六角螺丝 | {"直径":"M12","长度":"35mm","图号":"M12*35*1.5丝","螺纹长度":"30-32mm","材质":"Q235","表面处理":"发黑","性能等级":"10.9","使用寿命":"180天","参照标准":"GB/T 16938-2008","备注":"1.外观良好,无断丝、错丝.\n2.到货验收不符合技术要求,必须退换货,产生的费用由供应商承担."} | 500.00 | 套 | |
| 平键 | {"型号":"22*14","宽度":"22mm","高度":"14mm","长度":"1000mm","材质":"Q235","使用寿命":"365天","参照标准":"GB/T 1096-2003","备注":"该到货产品与技术要求不符，对该到货产品进行10%处罚或调换退货，调换货产生的费用由供货方承担。"} | 500.00 | 米 | |
| 平键 | {"型号":"30*18","宽度":"30mm","高度":"18mm","长度":"1000mm","材质":"Q235","使用寿命":"365天","参照标准":"GB/T 1096-2003","备注":"该到货产品与技术要求不符，对该到货产品进行10%处罚或调换退货，调换货产生的费用由供货方承担。"} | 500.00 | 米 | |
| 平键 | {"型号":"25*14","宽度":"25mm","高度":"14mm","长度":"1000mm","材质":"碳钢Q235","使用寿命":"≥90天"} | 500.00 | 米 | |
| 不锈钢扎带 | {"规格型号":"长350mm宽7.9mm厚0.25mm","螺纹外径":"无","五星外径":"无","螺杆长":"无","材质":"304不锈钢","螺纹镀锌层厚度":"无","外观":"表面平整光泽","螺纹长度":"无","使用寿命":"1095天","参照标准":"GB/T 3280","备注":"扎力紧实不脱扣，表面平整光泽，边缘应无锐角、毛刺或缺口。如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 500.00 | 个 | |
| 不锈钢扎带 | {"规格型号":"长450mm宽7.9mm厚0.25mm","螺纹外径":"无","五星外径":"无","螺杆长":"无","材质":"304不锈钢","螺纹镀锌层厚度":"无","外观":"表面平整光泽","螺纹长度":"无","使用寿命":"1095天","参照标准":"GB/T 3280","备注":"扎力紧实不脱扣，表面平整光泽，边缘应无锐角、毛刺或缺口。如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 500.00 | 个 | |
| 不锈钢扎带 | {"规格型号":"长650mm宽7.9mm厚0.25mm","螺纹外径":"无","五星外径":"无","螺杆长":"无","材质":"304不锈钢","螺纹镀锌层厚度":"无","外观":"表面平整光泽","螺纹长度":"无","使用寿命":"1095天","参照标准":"GB/T 3280","备注":"扎力紧实不脱扣，表面平整光泽，边缘应无锐角、毛刺或缺口。如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 500.00 | 个 | |
| 不锈钢扎带 | {"规格型号":"长850mm宽7.9mm厚0.25mm","螺纹外径":"无","五星外径":"无","螺杆长":"无","材质":"304不锈钢","螺纹镀锌层厚度":"无","外观":"表面平整光泽","螺纹长度":"无","使用寿命":"1095天","参照标准":"GB/T 3280","备注":"扎力紧实不脱扣，表面平整光泽，边缘应无锐角、毛刺或缺口。如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 500.00 | 个 | |
| 不锈钢扎带 | {"规格型号":"长1300mm宽12mm厚0.25mm","螺纹外径":"无","五星外径":"无","螺杆长":"无","材质":"304不锈钢","螺纹镀锌层厚度":"无","外观":"表面平整光泽","螺纹长度":"无","使用寿命":"1095天","参照标准":"GB/T 3280","备注":"扎力紧实不脱扣，表面平整光泽，边缘应无锐角、毛刺或缺口。如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 500.00 | 个 | |
| 不锈钢扎带 | {"规格型号":"长900mm宽12mm厚0.25mm","螺纹外径":"无","五星外径":"无","螺杆长":"无","材质":"304不锈钢","螺纹镀锌层厚度":"无","外观":"表面平整光泽","螺纹长度":"无","使用寿命":"1095天","参照标准":"GB/T 3280","备注":"扎力紧实不脱扣，表面平整光泽，边缘应无锐角、毛刺或缺口。如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 500.00 | 个 | |
| 螺栓 | {"型号":"M12*40","图号":"00.066.011","材质":"图纸未标注","所属设备名称":"中压后汽封-136.068Z+低压后汽封-136.069Z","设备型号":"C135/N150-13.24/0.981","设备生产厂家":"哈尔滨汽轮机有限责任公司","国产/进口":"国产","特殊要求":"无","参照标准":"DLT 991-2006","备注":"物资是汽轮机厂根据汽轮机组的运行要求，自行设计出的零件，图纸上未明确标注国标等可能参照的标准，在此仅标注一下汽轮机合金钢材质件到货验收时常用的标准。照片也仅是提供参考，实际供货已厂家图纸为准。本物资图纸未明确标注材质，供应商应按厂家图纸标注的材料供货，并提供材质报告单。"} | 500.00 | 个 | |
| 强扭力皮带扣 | {"型号":"12*14","图号":"无","材质":"优质碳素钢","厚度":"2.5","调整范围":"无","形式":"锤击式","克重":"0","允许偏差":"±0.1mm","所属设备名称":"带式输送机","设备型号":"B1000","设备生产厂家":"任何符合生产此物品的厂家","国产/进口":"国产","使用寿命":"≥365天天","特殊要求":"选用优质碳素结构钢整体顺纹冲压成型,扣手部位采用不切槽整体挤压成型,有很高的抗拉强度,安装速度快,钉子隐藏,对滚筒磨损较小,适用带厚9-11mm.","参照标准":"MT/T 319-2006","备注":"易耗品,属于SK单体六钉扣,适用煤矿织物整芯阻燃输送带机械接头用带扣,也适用于其他用途的织物芯输送带机械接头用带扣,强度等级1400N/mm的输送带连接.装订方式:锤击式.,单面厚度:2.5±0.1mm,带扣表面应光滑均匀,不得有斑疤毛刺.到货物资如与技术要求不符或存在质量问题,厂家负责免费退换货处理,所产生的费用由厂家负责."} | 500.00 | 个 | |
| 双头螺栓 | {"直径":"M32","长度":"170mm","材质":"45#钢","性能等级":"8.8级","使用寿命":"365天"} | 500.00 | 个 | |
| 定位销 | {"规格型号":"Φ8*60","材质":"中碳钢","使用寿命":"0"} | 500.00 | 个 |
| 投标厂商资质 | |||
| 注册资金 | 专业资质 | ||
| 公司业绩 | |||
| 相关认证 | |||
| 其他 | |||
